Hand Mitered Eavestrough Corners

PreMade Corner

Some other installers might use pre-made corners. Pre-made corners may be installed by someone who may not be proficient at hand mitered corners. They have more seams, requiring more caulking and are more likely to start leaking. The cleanest and neatest corner would be a hand mitered corner, done well. Our installers are all trained on how to install a very good hand mitered corner.





North Shore Eavestroughing and mitered corner

We can provide an industry leading warranty for you because our installers are well trained to provide you with a top-notch installation.  Most corners are 90 degree, inside or outside corners, but there also non-standard angles such as on turrets and bay windows.





Geocel provides a waterproof seal

The installer measures the length of the eavestrough required, cuts a 45 degree angle on each side and brings together to make a 90 degree corner. One side is smooth and the other has tabs cut into it. Our installers screw these  together, trim the edges, hammer to smooth any rough parts and caulk using a special Geocel sealant. Unlike other products this sealant is not affected by temperature so need to worry that the weather is too hot or too cold on your installation day. Geocel can even tolerate a bit of moisture.

Remember, we are not a roofer that does eavestroughing. We specialize in eavestroughs and have done so for over 20 years.

The type is pretty small on sealant can but here is what it says ” 2320 Gutter and Narrow Seam Sealant is a single component, extremely durable, flexible tripolymer sealant that forms a watertight seal in small joints and narrow seams. 2320 can be applied under any weather conditions, even through standing water or on oily surfaces. Guaranteed adhesion to metal, glass, vinyl, brick, stone, concrete , wood and asphaltic materials.”



This picture shows  a hand mitered corner done by North Shore Eavestroughing. This will give you many leak proof years and has a clean look to it.






Choices in Replacing Your Eavestroughs

Heavy .032 gauge aluminum eaves for commercial application

Perhaps your eaves are old, damaged, leaking, the downspouts are in the wrong places or you don’t like the colour. You have decided to replace your eaves. Now you have more decisions to make.

Placement of Downspouts: This is something our estimators look into with every quotation. You may be required to disconnect your downspouts from the city sewer pipe. In many cases it might be best to install new eaves on a different slope sending the water to a more optimal location. Our estimators would be happy to discuss this with you. Even if your municipality is requesting that you disconnect, sometimes this is not reasonable. You may need to apply for an exemption from the bylaw. These are things that our estimator can discuss with you.

Roof Integrity:  How old is your roof ? Yep, you need to replace your eaves and now I am suggesting you consider a much larger expense. If the roof  needs to be replaced, it is best to do that before we install new eaves.

Weight of Aluminum: Residential jobs are usually done in .024 gauge aluminum. It is the right weight for most jobs, comes in many colours and is the lowest price. If you have an extremely large roof or one that has a steep valley coming down to a small section of eaves, you might consider getting . 027 or.032 gauge for maximum strength. Colour selection is reduced and price goes up. We usually recommend the Alu-Rex Leaf guard. As well as keeping the leaves and debris out of your eaves, they add plenty of strength to your installation.

Colour: Do you want to keep the same colour?  If your soffit and fascia are white or an off-white, you might consider choosing a different colour for your eaves. If your soffit and fascia are colours, you probably want to stick with the same colour for your eaves. If you are considering a change, we suggest you match the eaves with the colour of your window and door frames, or the roof, or the your outside railings or walls. Some people choose one colour for the eaves and another for the downspouts so they can blend in with the walls. If a downspout goes on top of the roof, you might prefer it matches the roof colour. If a downpipe ends in a flower bed, we can make that last section brown, so it is not as noticeable.

Downspouts come in a number of sizes, too. In PEI we usually install small square 2.5″ x 2.5″ In Toronto, we usually install 3″x 3″ large square. We can get 3.5″x 3.5″ Extra Large downpipes, if you have a huge amount of water draining quickly. The best colour selection is in the 3″x3″ size. It is also possible to get 2″x3″ or a commercial size 3″x 4″. We don’t usually carry these.

Our estimators will be more than happy to discuss these and other issues with you, whether you meet them on site or discuss these by phone or e-mail.




HomeStars Best of 2013 Awards Party

HomeStars is an awesome tool for you to connect with quality contractors. A homeowner can visit Homestars and see a list of contractors in many different categories. The best part is that you can see the reviews that other homeowners have wrote about a contractor, good or bad. With that information you can pick contractors you feel comfortable reaching out to and talk or meet about a project you need completed.

Continue reading “HomeStars Best of 2013 Awards Party”

Professional Lettered Equipment

We never get a second chance to make a first impression. North Shore Eavestroughing believes that we must portray an image that is consistant with the high standards we have for working on your home. Clean, well lettered vehicles can be one way to determine how much pride a company takes in their day to day operations. Companies that take pride in their work and operate without subcontractors generally have well lettered company vehicles. This is a great way to pre-qualify potential contractors no matter what the trade.

Continue reading “Professional Lettered Equipment”